⚠WARNING: Riding an electric mini bike can be a hazardous activity. Certain conditions may cause the equipment to fail without fault of the manufacturer. Like other electric products, these vehicles can and are intended to move, and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care, instruction or expertise can eliminate. If such things occur you can be seriously injured or die, even when using safety equipment and other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.

This manual contains many warnings and cautions concerning the consequences of failing to maintain, inspect or properly use your electric mini bike. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such a possibility is mentioned.

APPROPRIATE RIDER USE ANDPARENTAL SUPERVISION

This manual contains important safety information.

It is your responsibility to review this information and make sure that all riders understand all warnings, cautions, instructions and safety topics and assure that young riders can safely and responsibly use this product.Recommend that you periodically review and reinforce the information in this manual with younger riders, and that you inspect and maintain your child’s product to insure their safety. The recommended rider age is only an estimate, and can be affected by the rider’s size, weight or skills. Any rider unable to fit comfortably on the Mini Bike should not attempt to ride it. A parent’s decision to allow his or her child to ride this product should be based on the child’s maturity, skill and ability to follow rules.

DO not exceed the maximum recommended rider weight.

⚠WARNING: 

Rider weight does not necessarily mean a person’s size is appropriate to fit or maintain control of the vehicles.

Keep this product away from small children and remember that this product is intended for use only by persons who are completely comfortable and confident when operating the products.

Do not touch the brakes or electric motor on your electric mini bike when in use as they can become very hot.

Refer to the section on safety for additional warnings.

ACCEPTABLE RIDING PRACTICES AND CONDITIONS

Always check and obey any local laws or regulations which may affect the locations where the vehicles may be used.

Ride defensively. Watch out for potential objects that could catch your wheel or force you to swerve suddenly or lose control. Be careful to avoid pedestrians, skaters, skateboards, scooters, bikes, children or animals who may enter your path, and respect the rights and property of others.

The Mini Bikes are meant for use only in controlled environments free of potential traffic hazards and not on public streets or sidewalks. Do not ride your electric mini bike in any areas where pedestrian or traffic is present.

Do not activate the speed control on the hand grip unless you are on the electric mini bike and in a safe, outdoor environment suitable for riding.

These bikes were manufactured for performance and durability but are not impervious to damage. Jumping or other aggressive riding can over-stress and damage any product, including the electric motorbike, and the rider assumes all risks associated with high-stress activity.

Be careful and know your limitations. Risk of injury increases as the degree of riding difficulty increases. The rider assumes all risk associated with aggressive riding activities.

Maintain a hold on the handlebars at all times.

Never carry passengers or allow more than one person at a time to ride the electric mini bike.

Never use near steps or swimming pools. Keep your fingers and other body parts away from the drive chain, steering system, wheels and all other moving components.

Never use headphones or a cell phone when riding.

Never hitch a ride with another vehicle.

Do not ride the vehicles in wet or icy weather and never immerse the electric mini bike in water, as the electrical and drive components could be damaged by water or create other possibly unsafe conditions. These vehicles are intended for use on flat, level ground without loose debris such as rocks or gravel. Wet, slick, bumpy, uneven or rough surfaces may impair traction and contribute to possible accidents. Do not ride the electric mini bike in mud, ice, puddles or water. Avoid excessive speeds that can be associated with downhill rides. Never risk damaging surfaces such as carpet or flooring by use of an electric mini bike indoors. Do not ride at night or when visibility is limited.

PROPER RIDING ATTIRE

Always wear proper protective equipment such as an approved safety helmet (with chin strap securely buckled). A helmet may be legally required by local law or regulation in your area. Elbow pads and knee pads, a long-sleeved shirt, long pants and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles), never ride barefooted or in sandals, and keep shoelaces tied and out of the way of the wheels, motor and drive system.

USING THE CHARGER

The charger supplied with the electric mini bike should be regularly examined for damage to the cord, plug, enclosure and other parts, and in the event of such damage, the bike must not be charged until the charger has been repaired or replaced.

• Useonlywith the recommended charger. Do not use Lead-Acid charger with Li-ion battery and vise versa.
• Use the original charger.
• Usecautionwhen charging. The charger is not a toy and should be operated by an adult.
• Do not operate charger near flammablematerials.
• Unplug charger and disconnect frombikewhen not in use.
• Chargers are not waterproof andshouldnever be used in wet conditions. Serious injury or death could result.

FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.

Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because these vehicles are 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents.

MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.

Recommends assembly and maintenance by an adult. Allow up to 30 minutes for assembly.

The Minibike allow up to 12 hours for initial charge (see page 8-9 for charging information).

During assembly, you can familiarize yourself with the vehicles components and design.

Enjoy the process and take your time to insure all components are safe and secure!

⚠WARNING:
DO NOT USE NON- ORIGINAL PRODUCTS WITH YOUR VEHICLES.
These vehicles have been built to certain design specifications. The original equipment supplied at the time of sale was selected based on its compatibility with the frame, fork and all other parts. Certain after market products may or may not be compatible and may void your warranty.

ADDITONAL PARTS LOCATION
Located within the center packing foam you will find the charger and tool kit. Within this package the handle bar clamps and hardware are also located. DO NOT DISCARD.

All electric motorbike are set on low speed when they are shipped. You should change this setting only when you feel the rider can control the vehicle at higher speeds.

Lithium iron phosphate battery
Your new electric motorbike is partially charged from the factory. Charge before Riding

Standard phosphoric acid
To achieve the best performance and life from your new battery, the first charge and full discharge cycles are important. After the first charge-Run the battery down (not dead) and then recharge completely. This will format the battery. To get the longest life out of your lithium iron phosphate batteries recharge them Completely after every ride, even very small rides. Leaving the battery pack in a partially discharged state may cause internal produce oxide of the batteries which lowers the useful lifespan of the batter pack.

• Initial charge time up to 12 hours
• Recharge time: up to 8 hours, depending on level of depletion.
• Fully charge battery before storing.
• When the motorbikeis not in regular use,recharge the battery at least once a month until normal use is resumed.

Standard Charger
Lithium iron phosphate battery
Green light means ready.
Red light means charging.

Note: Make sure power is turned OFF when unit is not in use. If the power switch is left on for an extended period, the battery may reach a stage at which it will no longer hold a charge.

⚠WARNING:
To avoid a pinch or injury keep fingers away from moving sprockets and chain.

⚠WARNING:
To prevent shock, please follow the instructions accordingly and do not skip or combine any steps.

⚠WARNING:
Rechargeable batteries are only to be charged under adult supervision. Always disconnect your electric motorbike from the charger before cleaning with liquid.
Note: If your charger does not look like the one illustrated, your unit may have been supplied with an alternative charger. The specifications and charging procedure would not change. The charger has a small window with one LED to indicate the charge status. A green light indicates the charger is ready to be plugged into the bike and a red light indicates charging. After the unit is fully charged the indicator will return to a green light signifying the ready condition. Refer to the illustration on the charger unit for the actual “charging” and “charged” status indications for your model charger. Chargers have built- in overcharge protection to prevent battery from being overcharged. Charger will get warm during use. This is normal for some chargers and is no cause for concern. If your charger does not get warm during use, it does not mean that it is not working properly.
Turn power switch “OFF” before charging and conducting any maintenance procedures.

Charging the Battery

Run time may vary depending on many factors such as riding conditions, rider weight, climate and/or proper maintenance, specifically tire pressure.

Phosphoric Acid Full recharge in 6 to 8 hours. Average battery life: 250 charge/discharge cycles. To get the longest life out of your batteries recharge them after every ride. Leaving the battery in a partially discharged state will lead to internal oxidation, thus reducing the performance and life of the battery pack. Do not charge in extreme temperature above 110° F or below 32° F.
Charging in extreme temperatures above 110° F and below 32° F can cause damage to battery. Always store in cool dry area with no more than 50% charge.

1.Plug the charger into a wall outlet FIRST. If the lights on charger do not light up, check the power to the outlet. If necessary, try a different outlet.

⚠WARNING:
Failure to recharge the Lead- Acid battery at least once a month may result in a battery that will no longer hold a charge.

⚠WARNING:
Lead acid and Li-ion battery chargers are not interchangeable. Make sure you are using the correct charger for the battery type you have. Serious damage could result.

Use only factory recommended battery charger for the battery type used!

Loose Parts
Check and secure all fasteners before every ride. Make sure handlebar clamp bolts are locked properly in place. There should not be any unusual rattles or sounds from loose parts or broken components. If you are not sure, ask an experienced mechanic to check.

Brake
Check the brake for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the speed control on, the brake cut-off switch will stop the motor. When the brake is not in use, the rear wheel should spin freely without drag.

Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames and chassis components are rare, it is possible for an aggressive rider to run into a curb or wall and wreck, bend or break a frame, fork or suspension components. Get in the habit of inspecting your regularly.

Tire Inflation
Tires are Not Fully inflated when shipped.
Using an air compressor equipped with a 45 degree end, inflate both tires to 5±0.5 PSI. Heavier riders us 5 PSI. This information is also located on the left side of the rear fork for easy access. Periodically inspect the tires for excess wear, and regularly check the tire pressure and re-inflate as necessary.

Safety Gear
Always wear proper protective equipment such as an approved safety helmet, elbow pads and knee pads. Always wear athletic shoes (lace-up shoes with rubber soles), never ride barefooted or in sandals, and keep shoelaces tied and out of the way of the wheels, motor and drive system.

WARNING: Turn keys “OFF” before conducting any maintenance procedures.

Adjusting the Brakes

To adjust the tension, thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment is attained. Most adjustments are complete at this step. If brake still needs further adjustment, proceed to step

⚠WARNING:

The brake can cause the electric motorbike to skid the tire throwing an unsuspecting rider. Practice in an open area free from obstacles until you are familiar with the brake function. Avoid skidding to a stop as this can cause you to lose control or damage the rear tire.

Note: Brakes adjusted to tight and dragging will cause excessive wear and poor performance.

Chain Adjustment, Rear Tire Replacement

Tools required: 10mm T-shaped socket wrench,10mm, 12mm,16mm and 18mm open wrench

1.Loosen screws and remove chain guard.

2.Replace the tire and remove the rear wheel bolts.

⚠WARNING:
Make sure power switch is in off position before performing any maintenance.

⚠WARNING:
To avoid a pinch or injury keep fingers away from moving sprockets and chain.

3.Replace the tire, loosen the rear wheel nut, and at the same time, separate the tire from the rear rocking. Remove three more screws and remove the disc brake disc.

4.Adjust chain tension to adjust chain tension to get about 1/2 inch free clearance. Free is not mandatory! The chain should move this amount with very little force. Loosen the rear wheel bolts first, and then tighten or loosen the chain adjusting bolts. The chain tension must be correct and the axle must be firmly tightened.

5.Tighten the rear axle nut. Reinstall the chain guard. Test ride. Re-adjust as needed.

Chain and Sprocket Notes: The chain will typically have a “loose spot” and “tight spot” corresponding with a sprocket rotational position. This is normal and common to all chain-driven products due to run-out tolerances

of the sprockets. The chain should be adjusted to the ideal tension with chain in the tightest spot.

Proper chain alignment must be maintained. The wheel must not be skewed. If the chain is noisy or rough running, check the lubrication, tension and alignment of the sprockets, in that order.

⚠WARNING:

To avoid a pinch or injury keep fingers away from moving sprockets and chain.

⚠WARNING:

Make sure power switch is in OFF position before performing any maintenance.

Battery Replacement.

Lithium phosphate batteries (36v 9ah) should be replaced in sets only and with original Batteries!

Retailers do not have the same quality as our OEM batteries. Performance may be seriously affected.

Disconnect battery connection.

Re-install new battery set and reconnect.

Prior to reconnecting the battery, ensure that the power supply is turned off to prevent any electrical sparks from occurring.

After assembling the battery, it is necessary to switch the air switch to the “on” position; otherwise, the power supply will be blocked.

Battery Care and Disposal (Lead-Acid)
Do not store the battery in temperatures above 110 °F or below 32° F.

Contains sealed non-spillable Lithium phosphate battery. batteries must be recycled.

Disposal: Our company product uses sealed Lithium phosphate battery which must be recycled or disposed of in an environmentally sound manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not dispose of a Lithium phosphate battery in your regular household trash. The incineration, land filling or mixing of sealed Lithium phosphate batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state approved Lithium phosphate battery recycler or a local seller of automotive batteries.

⚠WARNING:

To avoid a pinch or injury keep fingers away from moving sprockets and chain.

⚠WARNING:

To prevent shock, please follow the instructions accordingly and do not skip or combine any steps.

⚠WARNING:

If Lead-Acid battery leak

develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. Refer to the disposal instructions at left. If acid comes into contact with skin or eyes, flush with cool water for at least 15 minutes and contact a physician.

⚠WARNING:

Do not charge or discharge the battery in extreme temperatures.

Do not short-circuit the positive (+) and negative (-) terminals of the battery.

Do not immerse the battery into liquids or allow it to get wet.

The battery should be stored in a clean, dry area. Discharging and recharging the battery every 6 months is recommended.

Keep away from fire.

Do not disassemble the battery